搜索结果: 1-15 共查到“知识库 机械工程 INVESTIGATION”相关记录17条 . 查询时间(0.064 秒)
Experimental investigation on traversing hot jet ignition of lean hydrocarbon-air mixtures in a constant volume combustor
Jet Ignition Engine Wave Rotor Combustion
2015/1/12
A constant-volume combustor is used to investigate the ignition initiated by a
traversing jet of reactive hot gas, in support of combustion engine applications that include novel wave-rotor constant-...
Experimental Investigation into Combustion Torch Jet Ignition of Methane-Air, Ethylene-Air, and Propane-Air Mixtures
Torch Jet Hot Gas Jet Ignition Ethylene Methane Propane
2015/1/12
Ignitability and the ignition delay time of a combustible mixture in a long combustion chamber, ignited by a hot combustion torch jet generated in a pre-chamber was investigated experimentally in rela...
Experimental Investigation on Vibration Control of Rotor-bearing System with Active Magnetic Exciter
vibration control rotor-bearing system active magnetic exciter
2011/8/5
Vibration control is an efficient way to minimize a rotating machine’s vibration level so that its vibration fault-free can be realized. While，several factors, such as unbalance, misalignment and inst...
Numerical Investigation on Fluid Structure Interaction Considering Rotor Deformation for a Centrifugal Pump
centrifugal pump fluid structure interaction coupled solution
2011/8/5
The existing researches for unsteady flow field and the corresponding flow induced vibration analysis of centrifugal pump are mainly carried out respectively without considering the interaction betwee...
Experimental Investigation of Capacity Control Scheme on System Performance for a Machine Tool Cooler
machine tool cooler hotgas suction regulation capacity control
2011/8/4
Highly accurate manufacture in machining industry can only be obtained with precise temperature control of the coolant (oil or water). Machine tool with more accurate, stable and advanced the precisio...
Performance Investigation of Cone Dielectric Elastomer Actuator Using Taguchi Method
dielectric elastomer actuator performance objective Taguchi method
2011/8/4
Dielectric elastomer actuator (DEA) show promise for mechatronic applications due to the advantages of dielectric elastomer, such as lightweight, flexible, low cost, high strain, etc, and many configu...
Investigation on Flow Accelerated Corrosion Mitigation for Secondary Circuit Piping of the Third Qinshan Nuclear Power Plant
flow accelerated corrosion nuclear power plant secondary circuit piping
2011/8/4
Flow accelerated corrosion (FAC) is the main failure cause of the secondary circuit carbon steel piping in nuclear power plants. The piping failures caused by FAC have resulted in numerous unplanned o...
Performance Investigation of Cone Dielectric Elastomer Actuator Using Taguchi Method
dielectric elastomer actuator performance objective Taguchi method
2011/8/4
Dielectric elastomer actuator (DEA) show promise for mechatronic applications due to the advantages of dielectric elastomer, such as lightweight, flexible, low cost, high strain, etc, and many configu...
Use of SEM and EDS analysis in the investigation of Al-Si-Cu piston alloy cast porosity
casting porosity piston
2009/10/23
Porosity formation was detected in the casting thinnest section in the proximity of the as cast surface and near the wall centerline. In order to investigate the cause of the porosity formation light ...
Investigation of the coatings applied onto brake discs on disc-brake pad pair
coating improving disc performance Disc Thickness Variation (DTV)
2009/10/23
While braking, according to the severity of it, thermal, metallurgical, constructive and tribological occurrences emerge on the brake disc-pad interface. In this study, NiCr was sprayed as bonding lay...
Evaluation of Statistical Modeling Techniques in the Investigation of the Dimensions of Machined Components
Dimension measurement statistical modeling beta distribution function
2009/10/15
In this study, an investigation was conducted to find the behavior of the variation of the dimensions of machined workpieces collected for quality control purposes and to propose statistical distribut...
Investigation of the Friction Coefficient in Smooth Open Channel Flows
Open channel energy loss friction factor
2009/10/14
In practical engineering, the friction coecient formulations developed for circular pipes are usually assumed to be valid for open channels and used in derivation of mathematical formulation. However...
Investigation of the Friction Behavior of the Zinc-Aluminum Based Commercial ZA-27 Journal Bearing
Zinc-aluminum alloy plain bearing friction lubrication
2009/10/13
The zinc-aluminum based ZA-27 alloy was produced by permanent mould casting. Using this alloy and bronze obtained from commercial sources, thin wall journal bearings were manufactured by machining. Th...
Investigation of Turbulators for Fire Tube Boilers Using Exergy Analysis
Boiler Turbulator Fire Tube Effciency Exergy
2009/10/13
In this paper,an experimental study of ve di erent types of \turbulator" inserts for re tube boilers is presented. The experimental setup was constructed in the Department of Mechanical Engineering ...
Design,Manufacture and Investigation of Cracking Efficiency of a Stone Cracking Machine with Periodic Loading and Sloping Jaw
Stone cracking machine Apricot and Almond
2009/10/13
In this study, a stone cracking machine with periodic loading, and a shaky and sloping jaw which breaks apricot and almond stones was designed and manufactured. For determining the cracking eciency o...